HomeAbout UsQuality ControlManagement SetupProduct & ServicesProfileContact Us
 
 

Oil & Petroleum Testing Instruments

 
 
Products -> Oil & Petroleum Testing Instruments
 
[1]
 

PSAW REDWOOD VISCOMETERS (2501 to 2504)

These viscometers are designed for viscosity tests of petroleum Products. They confirm to require- ments of IP 70.Two adaption of Red Wood viscometer are. available No.1 for liquids having Red Wood flow 20 seconds to 2000 seconds and No.II for liquids whose flow time exceeds 2000 seconds. The complete out fit comprises hammer finshed Stainless steel bath with electrical heating arragment suitable to operate at 220 Volts AC Mains with tap, silver plated oil cup with precision stainless steel jet, cup cover, ball valve, thermometer- clip. Stirrer and M.S.Sheet stand with levelling screws.

CAT NO

RED WOOD VISCOMETER NO. 1

2501

Electrically Heated Model WithEnergy Regulator control

2502

Gas Heated (with Gas Burner)

2503

Electrically Heated With VoltageVarrier (copper coil).

2504

-with digital Indicator and controller & FHP Motor Stirrer & FHP Moter


CAT NO RED WOOD VISCOMETER NO. 2
2505
Electrical Heated with Energy Regulator Control
2506
Gas Heated (with gas burnor)
2507
Electrically Heated with Voltage Varrier (Copper Coil)
2508 With Digital Indicator and Controller & FHP Motor Stirrer

See Enlarge




RED WOOD VISCOMETER MULTIPLE APPARATUS ( 2509)

If consists , Two Red Wood No.1 cup and Two Red Wood No 2 cup are installed in the bath. The bath is made from S.S Sheet temperature is controlled by Electronic Digital Temperature Controller. The Stirring is done by FHP electric motor in the heating compartment. the unit has 4 sets of Oil Cup Covers, hermometer Clips and ball valve. Suitable to operate on 220 Volts AC circuits.

2501 a

IP 8C (0/450C x 0.20 C) low range thermometer

2501 b

IP 9C (40 x 85 0 Cx 0.2 0C) Medium Range Thermometer

2501 c

IP 10 C (76x1220Cx 0.20C) High range thermometer

2501 d

Flask Receiver 50 ml capacity

2501 f

Spare cup with valve for Redwood No 1

2501 g

Spare cup with valve for Redwoood No. 2

2501 i

Spare heater for Redwood No 1 Apparatus

2501 j

Spare heater for Redwood No 2 Apparatus

2501 k

Spare ball valve for Redwood No.1 and No 2 App.

2501 l

Stop Watch Electronic Model

2501 m

Stop Clock Table Model


See Enlarge




TAR VISCOMETER APPARATUS

As per IP 72 And is 1206 Standards. It is used for determination the viscosity of road oils and cut back bitumen. If consists S.S. Bath with cup of 10 mm or 4 mm oriface and sleeve, Stirrer with lifting clip and ball. The assembly kept on suitable stand with levelling Screws. Suitable to operate on 220 Volts AC Mains.

2510

Electrical Heating with Energy Regulator Control

2510 A

Electrical Heating with Voltage Varrier (Copper Coil)


See Enlarge




TAR VISCOMETER MULTIPLE APPARATUS

Consist 2 cups in a S.S Water Bath mounted on Stand with levelling feet fitted with 1000 watts ISI marked heater. Temprerature is controlled by DIGITAL ELECTRONIC CONTROLLER with F.H.P electric motor stirrer. Supplied with one Tar Cup 10 mm and one 4 mm orifice with valves PSAW 2511 Tar Viscometer Multiple Apparatus
OPTIONAL ACCESSORIES Price In

2510a
Spare Silver Plated Cup 10 mm or 4 mm orifice
2510 b
Measuring Cylinder 100 ml cap
2510 c
IP8C (0/450Cx 0.20C) Low Range Thermometer
2510 d
IP9C (40X850Cx.20C) Medium Range Thermometer
2510 e
IPI0C (76x1220Cx0.20c) High Range Thermometer
2510 g
Spare Heater 400 W
2510 h Electronic Stop WAtch

See Enlarge




ENGLER VISCOMETER APPARATUS

2512

Electrical Heating with energy regulator control

2512 a

Electrical Heating with Voltage Varrier (Copper Coil)

OPTIONAL ACCESSORIES

2512 a

Engler ASTM 24C Thermometer (39/540Cx0.20C)

2512b

Engler ASTM 25C Thermometer (95/1050Cx0.20C)

2512 c

Ebonite Valve

2512d

Spare Wooden Valve

2512e

Flask 200 ml Capacity

2512 g

Spare Heater for above


See Enlarge




SAYBOLT VISCOMETER APPARATUS

Made as per ASTMD-88 specification with Universal and Furol Jets made of Stainless Steel. Stirring is done by hand with turn table arrangement (without trainer, withdrawl Tube and Glass Wares). Suitable to operate on 220 Volts AC mains.

2514 Elect. Heating with Energy Regulator Control 136.50
2515 Elect. Heating with Copper Coil Voltage Varrier 240.00
2516 Two Saybolt Tubes Viscometer Elect. Heating with Control Pannel (Double Walled) with Digital Electronic Controller and F.H.P Stirrer

OPTIONAL ACCESSORIES

2514 a

Strainer for filtering oil 23.00

2514 b

Withdrawl Tube (Metal) 5.00

2514 c

Spare Cup without jets 49.00

2514 d

Spare jet universal 6.50

2514 e

Spare Jet Furol 6.50

2514 f

Flask 60cc. 8.50

2514 h

ASTM 17C Range 19 to 270C 00C Thermometer 11.50

2514 i

ASTM 18C Range 34 to 420C Thermometer 11.50

2514 j

ASTM 19C Range 49 to 570C Thermometer 12.00

2514 k

ASTM 20C Range 57 to 650C Thermometer 12.00

2514 l

ASTM 21C Range 79 to 870C Thermometer 12.50

2514 m

ASTM 22C Range 95 to 1030C Thermometer 12.50

2514 n

COMMEN RANGE Themometer 0-1000C 10.50



See Enlarge




KINEMATIC VISCOMETER BATH

This viscometer bath is used to maintain the correct constant Temprature for estimating kinemetic viscosity of oils & petroleum product. In this type of bath Various Viscometer may be fixed as an internal art of bath. The bath is rectangular in shape. Inside tank made of Stainless Steel Sheet. On two sides toughted glass provided for full visibility of objects. The bath is controlled by an electronic relay and Digital Contraller Temperature range 50C above room temperature to 1000 C. Accuracy 0.10C Stirring is done by a F.H.P elect. motor stirrer. It is supplied with viscometer tube holders and S.S. cover.

2519

Kinematic Viscometer Bath of chamber size 12”x9”x12” deep for 4 viscometer with Digital Temp. Indicator & controller
2521
Kinematic Viscometer Bath of chamber size 12”x12”x12” deep for 6 viscometer with Digital Temp. Indicator & controller
2521A
Kinematic Viscometer Bath with REFRIGERATION SYSTEM Temp. Range 00 to 1000C
2222B Kinematic Viscometer to accomodate 3 glass Viscometer Tubes with round glass vessel. Digital Temp. Controller with Indicator
Suitable up to 120C Temp. accuracy 0.10C

OPTIONAL ACCESSORIES

2519 a Viscometer U tube BS/USize A,B,C,D,E,F,G, & H
2519 b Viscometer U Tube Reverse Flow ( for opaque)Size 2,3,,4,5,6,7,8,9,10 & 11
2519 c Viscometer cannon Fenske, Direct Flow BS/IP/CF Viscority rangeSize 15,50,100,150,200,250,300,350,400,450,500 & 600
2519 d Viscometer Cannon Fenske Reverse FlowSize 100,150,200,300,350,400,450,500 & 600
2519 e Viscometer suspended level BS/IP/SL Size 1,1A, 2, 2A,3, 3A,4
2519 f Spare Viscometer Holder
2519 g Electronic Stop Watch
2519 h Stop Clock Table Model
2519 i Lighting Attachment

Note :- Please mention Size and Viscosity range of Viscometer tube with indent . The Viscometers supplies with Constant Certificate.

See Enlarge




FLOW CUP VISCOMETER

This type of cup has been in popular use for amny years and confirms to IS 3944-1965 specification. These are available in following sizes. Jet No. B-1,B-2,B-3 &B-6

2518

Flow cup viscometer

2518 A

Spare brass cup with any size jet


See Enlarge




ABELS FLASH POINT APPARATUS

2520 A

Abels Flash Point App., Elect. Heating With Energy Regulator Control

 

A   Oil Test Jet
B   Gas Test Jet
2521A -same as above – but with Concealed Hot Plate  
A   Oil Test Jet
 B   Gas Test Jet
2522A

Abels Flash Point App. With - Voltage Veriac Control-  
A   Oil Test Jet
 B   Gas Test Jet
2523 A Abels Flash Point App with voltage varrier . &. Digital Temp. Indicator -Same as Above- with FHP. Elect. Driven Stirrer  
A   Oil Test Jet
 B   Gas Test Jet
C   Oil Test Jet
D Gas Test Jet
2524A bel Flash Point app. Temp Range –180C to +700C With REFREGERATION SYSYTEM as per IP-170 With oil Test Jet & Gas Test jet combine system

See Enlarge




OPTIONAL ACCESSORIES

2520 a

Abel Oil Cup Thermometer(-35/700Cx005C) IP 74 C

2520 b

Abel Water Bath Thermometer (-30/800Cx005C) IP-75 C

2520 d

Spare cup for above apparatus

2520 e

Spare Top (Cover assemble) with shutter mechanism

2520 f

Spare Nichrome heating Element

2520 g

Pendulum for Measuring Time in Strokes

2520 h

Concealed Hot Plate with Housing


See Enlarge




PENSKY MARTEN FLASH POINT APPARATUS

This apparatus is made as per IP 34, ASTMD –93 and IS 1448 (Part I) 1270 (P.221) and IS 1209-1953 method B. The Apparatus consists of brass test cup with handle removable cup cover with spring operated rotating shutter having Oil Test Jet/Gas Test Jet Flame Device Stirrer with flexible shaft. The assembly rests in Air Bath, which is covered, with Dome shape metal top. The cup is fitted with insulated Handle and Locking arrangement near cup flange, The assemble is kept on round shape electric heater with temp. Regulator. Suitable for operation on 220 Volts 50 cycles AC Circuits

255A

Pensky Marten Flash Point Apparatus. Elect. Heated with Energy Regulator

A

Oil Test Jet

B

Gas Test Jet

2526A

P.M Flash Point app. Elect. Heated with Concealed Hot Plate and Energy Regulator

A

Oil Test Jet

B

Gas Test Jet

2527 A

P.M Flash Point app. Elect. With Energy Regulator , & Hot plate. FHP. Motor Stirrer

A

Oil Test Jet

B

Gas Test Jet

2528A

P.M Flash Point App.With voltage variac Control and concealed Hot Plate

A

Oil Test Jet

B

Gas Test Jet

2528 A

P.M. Flash Point App. Voltage Variac with F.H.P Elect. Motor Stirrer

A

Oil Test Jet

B

Gas Test Jet

2530A

Pensky Marten Flash Point App. With Voltage Variac And Electronic Digital Temp. Indicator

A

Oil Test Jet

B

Gas Test Jet

2531

Semi Automatic Flash Point App. With electronic Temp. Controller, Automatic Dipping cycle withremote control Oil Test jet or Gas Test Jet

OPTIONAL ACCESSORIES

2525 a

Openclip for converting close model to open cup test model as per IP 35

2525 b

IP 15 C Low range (-7/110Cx0.50C) thermometer

2525 c

IP 16 C High Range (90x370Cx20C) thermometer

2525 e

spare cup with handle

2525 f

spare cover assembly

2525 g

spare nichrome heating element

2525 h

spare conceated hot plate with housing


See Enlarge




CLEAVELAND FLASH POINT & FIRE POINT APPARATUS

This apparatus is used for determination of flash point of petroleum products except fuel oil with open cup flash below 80°C as per specification IP 36 and IS : 1448 (P : 69) 1969 The apparatus consists of a cup, heating plate to specific demension thermometer clip & test flame attachment with swivel joint for passing
over test liquid surface in the prescribed manner, Heating is controlled by means of energy regulator fitted to the apparartus. Suitable of adperation on 220 Volts 50 cycles AC circuits.

2532

Cleaveland Flash Point & Fire Point Appartus Electrical Heating with energy regulator Gas Test Jet

2533

With oil wick arrangement

2534

-same as above- Gas Jet& Oil wick arrangement combined model

2535

Cleaveland Flash Point & Fire Point Appartus voltage variac (Copper Coil) Combine Model

2536

-same as above- with Digital TEmp, Indicator

2532 a

Thermometer IP 28C(-50C to 4000C)

2532 c

Spare cup with handle

2532 d

Spare nichrome element

2532 e

L.P.G Test flame container with valve


See Enlarge




PENETROMETER APPARATUS

This apparatus is used for penetration test on a wide variety of materials such as greases, petroleum, bitumen, tar, wax, polish, food stuff, rubber asphalts and pharmaceuticals creams. A given force is applied over a given period of times and the depression is made in the sample which is measured is tenths of a millimeter and express as penetration. It consists of a head support mounted on a vertical rod which can be adjusted for height. A rach and pinion and pointer assembly provides fine adjustment of needle tip to sample and in corporates a slipping clutch mechansium which make reading of penetration and aud subsequent resetting a
sample and accurate operation. The dial graduate from 0-400 in one tenth millimeter Sub Division. The Instrumets is supplied with sample containers.

2537

Penetrometer Apparatus with containers and weight having penetration Needle

2538 a

Penetrometer Apparatus with container and weights having peneteration CONE HOLLOW type

2538 b

-same as above- but with verier height adjustment system

2539

Penetrometer Apparatus with Electronic TIMMER & electrical arrangement with brass cone and Needle with DIGITAL TIMMER DEVICE (Adjustable)

OPTIONAL ACCESSORIES

2537 a

Spare penetration Needle (Pack of two) 8.00

2537 b

Spare penetration Solid Cone 19.50

2537 c

Spare penetration Brass Hollw Cone 19.50

2537 d

Grease Worker Hand Operated 110.00

2537 e

Grease Worker Hand Operated Big Handle (Lever type) 143.00

2537 f

Grease cutter as per IP 50 65.00

2537 g

Transfer dish


See Enlarge




DISTILLATION APPARATUS

This apparatus is used for determination of distillation chracterstics of petroleum products. The Instruments consists of metals shield to support distillation flask with GEARED HEIGHT ADJUSTABLE DEVICE. It has a slot of vapour tube. A glass window is provided in front side for clear view of inside objects. It also has colling bath or condersor with M.S black painted stand Electrically Heated. The Instruments is supplied with two square asbestos boards with 50 mm and 70 mm holes. (Without glass wares)

2540

Single Distillation Apparatus electrically heated with energy regulator with gear device

2541

Single Distillation Apparatus with voltage varrier (Copper Coil) with gear device

2542

Twin (Duplex) Distillation Apparatus Elect. Heated model with two energy regulators with gear device

2543

Twin (Duplex) Distillation Apparatus with two voltage verriers (Copper Coil) with gear device

2544

Distillation Apparatus for crude Petroleum as per IP-24 with one glass condensor elect.. with Energy Regulator control

OPTIONAL ACCESSORIES

2540 a

Distillation Flask 125 ml 10.00

2540 b

Distillation Flask 250 ml 13.00

2540 c

Measuring Receiver 100 ml 11.50

2540 d

Spare Asbestos Board 38 mm or 50 mm or 70 mm Dia hole 3.25

2540 e

Thermometer IP 5C (-2/3000Cx1C) 10.50

2540 f

Thermometer IP 5C (-2/4000Cx1C)


See Enlarge




BOMB CALORIMETER APPARATUS

It is used for determination of heat of combustion, calorific value and sulpher contents of solid and liquid fuels. The Bomb Body and lid are machined from corrosion resisting stainless steel rod its capacity is appox. 300 ml. It is provided with high pressure valve and electrodes. The calorimeter vessel, water jacket, Stirrer FHP motor driven are provided as per IP sandards. The Bomb Colorimeter is supplied with firing unit, Elect -ronic Digital Thermometer, Pellet Press, Ignition wire, and pressure guage on stand with copper pipe fitting.

2545

BOMB CALORIMETER APPARATUS With Digital Thermometer 0.10C read out.

2546

BOMB CALORIMETER APPARATUS Digital Thermometer with 0.010C Read with Remote Control Unit

2545 a

Spare Bomb 300 ml Cap.

2545 b

Spare Neoprene washer for Bomb

2545 c

Spare Stainless Steel Crucible


See Enlarge




CARBON RESIDUE APPARATUS (RAMSBOTTOM)

It is made as per IP 14, ASTM 524 and IS 1448 (P :8)-1967 standrads. It is used to determine the amount of carbon deposite when an Oil evoparated under specified condition. The apparatus consists of a solid metal bath having 5 wells to accomodate cocking bulbs, The Heavy Duty Heating elements provided
around the bath. Supplied with 5 cooking bulbs, and one syrings.

2547

Rams botton Carbon Residue Apparatus with temp. regulation by energy Regulator, Thermocouple and Digital temp.Indicator in seperate cabinet

2549

Rams botton Solid state electronic digital temperature controller PID type in seperate unit

OPTIONAL ACCESSORIES

2547 a

Spare cocking Bulb

2547 b

Spare Heating Element for above

2547 c

Spare Syrings

2547 d

Stainless Steel Tong


See Enlarge




CARBON RESIDUE APPARATUS (CONRADSON)

It is made as per IP 13, ASTM D-189 specifications. It is useful to determine amount of Carbon residue when an oil is evaporated under specified conditions. The Carbon residue values of crude oil, residuam etc. These are useful in the manufacture of various libricants. The apparatus consists of spun sheet iron crucible
25 cc Capacity, Sheet Iron hood and sheet iron block on a stand, gas burnor.

2550

Conradson Carbon Residue single test apparatus

2551

Coneadson Carbon Residue Four Test Apparatus with gas burnor


See Enlarge




CLOUD & POUR POINT APPARATUS

This is made according to specification laid by IP by 15 & IS 1448 (P:10) 1970. The Pour Point is lowest temperature at which th oil will just fail to flow. The apparatus consists main cooling bath made out of S.S. Sheet and stand Unit with drain Plug and cover has provision for fitting thermometer and a filling aderture for adding freezing mixture. A Glass Jar for containing Oils, Jackets, Disc and gasket as specified are also provided.

2552

Cloud & Pour Single with Insulated Body

2553

Cloud & Pour Point Two test with Insulated Body

2554

Cloud & Pour Four Test With Insulated Body

2555

Cloud & Pour Point Six Test with insulated Body

2556

Cloud Pour Point app. WITH REFRIGERATION System (for 2 test app.) temp. upto-300C

OPTIONAL ACCESSORIES: -

2552 a

Cloud & Pour Point Thermometer IP IC 11.00

2552 b

Cloud & Pour Point Thermometer IP 2C 11.50

2552 c

Spare Glass Jar with cork 10.00

2552 d

Spare Metal Jacket with disc 10.00

2552 f

Rexine Dust Cover for Refrigeration Unit


See Enlarge




SOFTENING POINT APPARATUS

For determination of softening point of bituminious materials according to IP58 and IS 1205-1958. Softening point is that temprature at which the speciman under test becomes soft enough to alllow a steel ball of specific dimensions to fall a required distance under test condition. The apparatus consists of glass beaker, rings and ball guides, hand stirrer.

2561

Softening point apparatus (without glass beaker)

2562

Softening point apparatus with glass beaker

2563 a

Softening point apparatus with F.H.P elect.motor driven
stirrer and electric heater with temp. Regulator control

2563 b

---same as above--- with DIGITAL CONTROLLER UNIT

OPTIONAL ACCESSORIES

2561 a

Thermometer IP 60C 10.00

2561 b

Themometer IP 61C 10.00

2561 c

Spare ring with Ball-Centring Guide and Steel Ball (pack of 2)


See Enlarge




DROP POINT OF GREASE APPARATUS

As per IP 31 the apparatus consists of Brass Sleeve and case with metal cup and a glass boiling tube with Cork fitted to a bath 600 ml Beaker is provided. The assembly is kept on heater with energy regulator control and stand with F.H.P.elect. stirrer. As per IP 132 the unit comprises a glass beaker with fibre cover together with glass test tube with three indentations to receive Chromium plated brass cup. Cork for tube and a 1.5 mm diameter Brass Rod. The assembly is kept on heater with energy regulator and stand with F.H.P motor stirrer.

2564

Drop point apparatus as per IP 132 & ASTM D 566 152.50

2565

Drop point apparatus as per IP 31 152.50

OPTIONAL ACCESSORIES

2564 a

IP 40C Low Range Thermometer 10.00

2564 b

IP 41C High Range Thermometer 10.00

2564 c

IP 62C Drop Point Special Thermometer


See Enlarge




MELTING POINT APPARATUS

This apparatus consists of a cylindrical block of Aluminium with a bulit in electrical heating element. The mounted Alum . block illuminates from below by a lamp fixed in its housing. The aluminium block accept three capillary tubes and mercury thermometer. The temperature is controlled by riotary switch. The
magniflying lence provided for viewing objects clear. Suitable for operation on 220 volts AC circuits.

2566

Melting Point Apparatus 52.00

2567

Melting Point Apparatus Digital Temp. Indicator with cooling plug 153.00

2566a

IP 63C Themometer


See Enlarge




REID VAPOUR PRESSURE TEST APPARATUS

Made as per IP 69 & IS 1448 (P :39). 1967 elect. heated with FHP motor stirrer temp. controlled by Electronic Digital Temp. Controller and indicator
(Without Bomb & Accessories)

2557

Single Test Bath

2558

Double Test Bath

OPTIONAL ACCSSORIES

2557 a Vapour Pressure Bomb consisting of one Air Chamber One Gasoline chamber without cock
2557 b Gasoline Chamber with cock (If required)
2557 c Spare Airchamber only
2557 d NP Pressure Gauge for above

See Enlarge




COPPER STRIP CORROSION TEST APPARATUS

Double walled stainless steel chamber bath other chamber made of mild steel sheet attractive painted. As per IP 154 and IS 1448 (P-15) to accomodate 6 bombs. Temperature is controlled by Electronic Digital Controller (without S.S. Bomb)

2559 With Digital Temp. Controller & Indicator


OPTIONAL ACCESSORIES

2559 a

Stainless Steel Bomb

2559 b

Vice Single Strip

2559 c

Vice Four Strip

2559 d

Copper Strip (Pack of 3)

2559 e

Test Tube

2559 f

Copper Strip Comparison Chart (Indigenous)

2559 g

Inspection Tube (Flat)


See Enlarge




ANILINE POINT APPARATUS

2568

Aniline point apparatus as per IP 2 & IS 1448 (P- 3), ASTM D 611 method A complete with jaket (Without Thermometer)

2569

Aniline point apparatus as per IP-2 method B ASTM D 611 by thin film method B Elect. heated with elect. stirrer (Without Thermometer)

 

  • Spare tap

 

  • Spare Contraction Chamber

 

  • Spare Metal stirrer

2570

Aniline point apparatus as per IP-2 method ‘d’ by U-tube method elect.heated with FHP stirrer without thermometer

 

  • Spare ‘U’ tube

2571

Dean & stark app. for the estimation of moisture in lubricating oils as per IP-74,ASTM D in with one 10 cc receiver Flask, Condensor with clamp holder and Elect. Heater with Regulator


See Enlarge




SMOKE POINT APPARATUS

2572

Smoke Point Apparatus as per IP 57 & IS 1448 (P-31) & ASTM D 1322

2572 a

Spare Candle

2572 b

Spare Wick


See Enlarge




BURNING TEST LAMP

2573

Burning Test Lamp as per IP 10 & IS 1440 (P-5) & ASTM D 187-82

2573 a

Spare Wick

2573 b

Spare Chimney


See Enlarge




[1]


 
 

Home | About Us | Quality Control | Management Setup | Product & Services | Profile | Contact Us

Copyright 2008-2009. Popular Science Apparatus Workshops Pvt. Ltd.. All Rights are Reserved