|
T.L.C. Plate Storage Cabinet PSAW (716/13 ) For transparent and storage of coated plated, sealed against air humidity of size 388 x 23 x 20 cm.
See Enlarge
|
|
|
|
|
Draining Rack (716/14 ) For holding washed plates in angular position so that the water can drop off over the corner of wet plates before coating.
See Enlarge
|
|
|
|
|
Special Drying Cabinet (716/15 ) With inspection window takes 2 drying racks for T.L.C. plates upto 20 x 20 cm. The drying cabinet is suitable for activating T.L.C. carrier plates for heating of developed T.L.C. plates as well as for heating T.L.C. plates sprayed with detecting reagents. The resulting colour can be seen through the inspection window. Temperature range ambient temp. to 2500 C.
See Enlarge
|
|
|
|
|
U.V. Chromatography Inspection Cabinet PSAW (717 ) For viewing & detecting separated substances on T.L.C. layers fitted with long wave (365 mm.) U.V. lamp for use on 220 Volts A.C. All parts are powder coated.
See Enlarge
|
|
|
|
|
U.V. Chromatography Inspection Cabinet PSAW (718 ) For viewing & detecting separated substances on T.L.C. layers fitted with two different wave length U.V. tubes for use on 220 Volts A.C. All parts are powder coated.
See Enlarge
|
|
|
|
|
Ultra Violet Flouresence Inspection Cabinet, Dual Wave PSAW (719 ) Having imported filters with separate low pressure mercury vapour tubes for short U.V. (254 nm.) and long U.V.(365 nm) plus separate lamp for visible light. The low pressure mercury vapour tubes in this model facilitate immediate use for inspection as you switch on. All parts are powder coated.
See Enlarge
|
|
|
|
|
|
|
|
Chromatography Cabinet PSAW (721 ) made of wood with glass on all four sides and on top. Internal surface wax coated for solvent resistance. Hinged top provided with rubber gasket for air tight closing. Window with air tight door in lower portion. Heavy castors provided for easy movement. finished in natural colour nitrocellulose lacqure. Supplied with standard equipment viz. two stainless steel troughs and four glass rods. For accomodating 4 filter of 46 x 57 cms. size
See Enlarge
|
|
|
|
|
Rotary Vacuum Film Evaporator Buchi Type PSAW Model BU-6 (722 ) This model of evaporator is supplied complete with A.C. non-sparking geared drive unit, support stand filled with jack arrangement of stainless steel rod for positioning glass assembly, variable speed regulator, thermostatically controlled stainless steel water bath fitted on a jack, doubled coiled grass condenser with three opening for vacuum and cooling, pear shape evaporating flask capacity 800 ml. receiver flask capacity one litre with ball joint, feeling tube and vapour path tube, a compete working unit. All parts are powder coated with a epoxy/polyester hybrid textured siemens grey finish.
See Enlarge
|
|
|
|
|
Replacement parts for BU-6 Model PSAW (722A )
722A/01 |
Condener double coiled with S-35 ball joint cone |
722A/02 |
Gasket Seal |
722A/03 |
Vapour path tube B-24, B-29 |
722A/04 |
Feed Tube for condenser without teflon pipe |
722A/05 |
Receiver flask, with cup (Socket) jointcapacity 1000 ml. |
722A/06 |
Evaporating flask, kjeldhal capacity 800ml. B-24 socket |
722A/07 |
Evaporating flask, kjeldhal capacity 500ml. B-24 socket |
722A/08 |
Evaporating flask, kjeldhal capacity 300ml. B-24 socket |
722A/09 |
Evaporating flask, round capacity 1000 ml.B-24 socket |
722A/10 |
Tension spring to hold condenser |
722A/11 |
Clip to hold vapour tube and boiling flask |
722A/12 |
Water bath thermostatically controlledfitted on adjustable jack "PSAW" |
722A/13 |
Balls joint clip brass chrome plated |
722A/14 |
Sapare heater for water bath (ISI Marked) |
See Enlarge
|
|
|
|
|
Rotary Vacuum Film Evaporator Vertical Model Buchi Type Model BU-6V PSAW (723 )This model is almost similar to Model BU-6 but it is of vertical type. This enables an efficient short time condensation of solute and also requires less bench space.
See Enlarge
|
|
|
|
|
Replacement parts for Vertical Model PSAW (724A )
724A/01 |
Vertical double coiled condenser with a in-built trap having inlet and outlet for water circulation, outlet for vacuum on the top, ball joint for receiving flask at the bottom, a flange at the side for holding the condenser and a side tube for vacuum release. |
724A/02 |
Vacuum adapter for condenser to vacuum pump. |
724A/04 |
Vapour path tube B-24, B-29 |
724A/05 |
Gasket Seal |
724A/06 |
Feed Tube for condenser without teflon pipe |
724A/07 |
Receiver flask, with S-35 cup (Socket) joint capacity 1000 ml. |
724A/08 |
Evaporating flask, kjeldhal capacity 800 ml. B-24 socket |
724A/09 |
Tension spring to hold condenser |
724A/10 |
Clip to hold vapour tube and boiling flask |
724A/11 |
Ball joint clip brass chrome plated |
See Enlarge
|
|
|
|
|
Rotary Film Vacuum Evaporator Buchi Type Cold Trap BCT-6 PSAW (725 )This model incorporates a cold trap arrangement which enable cooling with solid bodies such as dry ice etc. This arrangement is very useful for freeze drying application and the concentration of very volatile solutions.
See Enlarge
|
|
|
|
|
Replacement parts Model for BCT-6 (726 )
726/01 |
Vertical double walled condenser with a in-built trap having outlet for vacuum on the side, ball joint for receiving flask at the bottom, a flange at the side for holding the condenser and a side tube for vacuum release. |
726/03 |
Vapour path tube B-24, B-29 |
726/04 |
Gasket Seal |
726/05 |
Feed Tube for condenser without teflon pipe |
726/06 |
Receiver Flask with S-35 cup (Socket) jointcapacity 1000 ml. |
726/07 |
Evaporating flask, kjeldhal cap. 800 ml.B-24 Socket |
726/08 |
Tension spring to hold condenser |
726/09 |
Clip to hold vapour tube and boiling flask |
726/10 |
Ball joint clip brass chrome plated |
See Enlarge
|
|
|
|
|
Rotary Vacuum Film Evaporator Buchi Type PSAW Improved Compact Model BU-6T (727 ) This model is similar to BU-6 but provided with specially designed quick action jack with enables the operator to lift or lower the complete glass assembly safely with a minimum effort. The jack is fitted on a 'T' shaped alluminium alloy base, light and stable. The bath is of stainless steel fitted with 1 Kw. heater which is mounted on a compact allumium alloy box. fitted with a thermostat for temperature control ±10C and a indicator light. All parts are made of non rusting material and are powder coated with a epoxy based paint.
See Enlarge
|
|
|
|
